CPJAI007 7Band wireless signal jammer

This model could be remote controlled by a digital system,could be manpack, each band is 10W, the frequencies could be customized, if in this table has not the frequencies that you need, plase contact us for customized, except for 5.8G, the frequencies customized will not need any additional money. 

Please contact with us at:
MS Rola
My phone:+86-13580038745
 
 
  

  Features
We use the The ultra high frequency wideband interference technique.
The effective power (channel power) is high and the interference radius is large.
Effective segmenting only interferes with the downlink and does not cause interference to the base station.
The design of the slow start circuit can avoid the fire phenomenon of the mechanical switch, and the integration is high and stable.
Perfect self protection function. When the device overheating, output power and standing wave fault alarm, the shielding device will automatically turn off the failure module to avoid shield damage.
All ports are waterproof and air joint, using professional waterproof case, without fear of exposed to wind and rain;
Integrated remote control system that can be maintained remotely through Internet without personnel arriving at the site;
Connection performanceAn AC 220V power input interface for connecting the power supply of the city, a RJ45 port for remote connection;
System accessories
The shield system you buy is made up of a host, an omnidirectional antenna, a RJ45 network communication cable, and a power cable.
Antennas
Type: Omnidirectional antenna
Gain :  3dbi.N type 
Pictures:

Vertical plane pattern:
  The RJ45crystal head of the net is connected with the joint,please find it as below:

Step1 Open the packing box

1. Open the packing box. The disassembled packing box is reserved for the purpose of moving or carrying it in the future.
2,Check the equipment and accessories is flawless and perfect open. If any of the existing defects or damage is found, please contact your supplier.
Step2 Connecting cable and antenna
1, connect one end of the RJ45 network communication cable to the RJ45 network communication port of the host, and the other end will access the network switch (the device can also directly connect to the computer when setting up the LANTRONIX XPort).
2, one to one connection between the antenna and the host port.
3,Inserting the AC INPUT power cord into the electric power supply socket.

Step3 switch on signal jammer

1,The power amplifier of the signal blocker begins to work, and the default is the maximum output power.
2,After opening the signal blocker, you need to do LANTRONIX XPort settings (IP address settings and Networking). Please see NMS user's Guide;
(Note: the device needs this step when the device first enters the net or changes the server, and it does not need this operation in other cases).
3,After setting up the XPort, you can control the equipment by remote operation software according to the actual situation of the field. See the details ofNMS user's Guide.

Step4 Control signal blocker

The use of remote control:
If the switch state is selected:
Left,right:Change the switch state
If the power amplifier attenuates:
Left:Every time the value is reduced, the attenuation value is equal to 31 when the attenuation value is less than 0.
right:The attenuation value is equal to 0 when the value is added each time, when the attenuation value is greater than 31.
OK:No matter what is selected, after determining the content to be set, press the OK key to save the settings and return to the setting interface mode0;
Touch settings:
After entering the setting interface;

Touch the content should be set;
If the power amplifier switch is set, the control becomes selected after the first touch:

Again touch, change the state of the switch, and save the settings, return to the setup interface display mode, mode0;


If the amplifier is set down, the first touch will jump to the small keyboard interface.

:The current channel number
:Cancel, click Exit;
:When you enter the correct settings, save and exit;
:Digital keyboard;
:clear-all;
:Delete one bit;
The effective input of the attenuation value is 0~31, which is invalid beyond this area;
After entering the valid attenuation value, click enter and return to the setting interface

Touch the settings again to save the settings and return to the settings display interface. Mode0 model;

Note: touch is not valid when using key mode and at mode1. When in mode0 and mode2 mode, touch is equally valid
The channel 5~8 is the same as the channel 1~4 operation.

Step5 Closing the signal blocker

1,The RF switch is turned off by remote operation software, and the power amplifier is stopped.
2,Disconnect the "AC~220V" AC power line with the city electricity.
3,Dismantle the RJ45 communication cable;

Matters needing attention

The antenna should be used vertically in the direction of the ground.
 The antenna must be connected first and then the power is connected. Do not take off the antenna when the host works.
The signal blocker should be placed in a well ventilated place to avoid the shielding of large objects as far as possible to ensure the shielding effect.
When using the shield in the outdoor, we should pay attention to the waterproof and fire prevention, and do not put the machine in wet, high pressure, high temperature, and strong magnetic field.
 If the signal blocker is not working or the light appears to be a problem, please contact the local dealer and do not disassemble and repair it by yourself.
 Any machine failure caused by man-made damage and bad operation can not be provided by the dealer for free maintenance.
 

CPJAI007 7Band wireless signal jammer

This model could be remote controlled by a digital system,could be manpack, each band is 10W, the frequencies could be customized, if in this table has not the frequencies that you need, plase contact us for customized, except for 5.8G, the frequencies customized will not need any additional money. 

Please contact with us at:
MS Rola
My phone:+86-13580038745