Gypsum board ceiling expensive expensive? Gypsum board ceiling has a good decorative effect and the price is cheaper than other materials, it has become the decoration of choice for the majority of ceiling decoration materials, the following small series for everyone to specifically introduce the price of gypsum board ceiling and gypsum board ceiling decoration and other issues.
First, the price of gypsum board ceiling
Gypsum board ceiling, according to its modeling process materials, etc., but the price is not the same, generally from 80 --- 140 yuan / square meter.
Ordinary ceiling 80 or so, if the use of light steel keel plus modeling prices naturally higher.
Second, gypsum board ceiling decoration process
1. Unlike general construction, preparatory work for ceiling construction is particularly important, including steps such as measurement and material selection. The good work done at this stage can greatly reduce the trouble in construction and guarantee the safety of future use. Before the formal construction, the worker first uses the horizontal pipe to measure the level of the ink line on the wall surface. Only when the actual level of the foundation line is ensured, the suspended ceiling installed later will not be tilted or there will be gaps.
2. The gypsum board ceiling needs to be fixed on a firm wooden keel frame, so careful selection of the keel material has become an indispensable step before. It is recommended that you try to choose the pine wood material that holds the nail strength better. Because the keel is wooden, fire precautions must be taken. The standard practice is to evenly paint the fireproof paint on the surface of the keel. When the whole keel is white, then it is nailed to the wall, which can ensure that it touches the wall. To fireproof paint.
3. The construction of suspended ceilings includes steps such as playing keel, plastering, handling of nail holes, caulking, and bandages, each of which is very important. Everyone in the renovation must strictly supervise whether the workers have done so. After the surface of the keel has been fireproofed, the combination can begin. Workers will use a nail gun to fix the two keel joints diagonally at 45 degrees. At this time, it is necessary to master the strength to prevent the keel from cracking.
4. After fixing the keel frame, it is necessary to fix the frame on the wall. At this time, it is necessary to carefully check whether the spacing between the frames is not more than 300 mm to have sufficient fastness. Otherwise, the gypsum board on it easily sinks and breaks.
5, the next step is to formally dry the board, it is best to allow workers to use drywall screws stainless steel fixed gypsum board, such nails will not rust, the future can guarantee the gypsum board a long time beautiful.
6, nails on the gypsum board is usually treated with rust-proof eye putty, and its practical cement to fill the nail is a more cost-effective way. And the effect after the treatment is not worse than nail eye putty. The gap between the two plasterboards must be handled in the next step, otherwise there will be obvious cracks in the future. General workers will use 901 glue and gypsum powder after mixing. Afterwards, it is best to use anti-crack tape on the surface to prevent the top surface from cracking due to thermal expansion and contraction. When sticking, pay attention to the use of a spatula to remove the air bubbles on one side and allow the tape and plasterboard to be completely and tightly combined.
7, the latter stage is the stage of special ceiling molding, the craftsmanship and experience of the workers directly affect the future appearance. Therefore, the decoration company should be asked to dispatch experienced workers to carry out the construction. For the special ceiling design, the post-processing is very important. The ceilings, such as circular and wavy, all require experienced masters to repair them slowly with a spatula. This is the most important process for forming the entire ceiling.
8, after repairing the basic shape, it is necessary to sand the edge of the ceiling again with sandpaper, removing the edges and edges of the edges. Must be patient and careful when handling, otherwise it will affect the appearance in the future.
Reminder: For more information, please pay attention to the information on this website , or you can visit our offline experience directly.
More exciting recommendations
AIA integrated ceiling
Integrated ceiling installation method
Kitchen integrated ceiling
Haichuang integrated ceiling
Xilinmen ceiling
Aopu integrated ceiling price
Suspended Ceiling Design Ceiling Mounting Paint Decorative Door Price Cement Furniture Ceiling Price Plasterboard Ceiling Ceiling Price AIA Integrated Ceiling Price Kitchen Integrated Ceiling
This classification including Australia standard AS1163 square steel pipe, usually they are used for construction purpose, also some customer use them for car , billboard, stents, fence etc.
Jinan Xin Jiyuan is specialized in ERW and
Seamless square&rectangular tube/pipe, hollow section structure pipe, and
galvanized pipe in China. Annual output reaches 1.5 million tons. We have 2 production
lines, could producte square pipe from 20*20*1mm to 600*600*35mm, rectangular
pipe from 20*30*1.2mm to 600*800*35mm. Xin Jiyuan can manufacture square
rectangular pipes as per the standards of ASTM A500, JIS G3466, EN10219, EN10210,DIN2240,
BS1387, AS1163. Steel
Grade: A500 GR.A/B/C/D, SS400, STKR490, S355JR, S275JO, S275J2, S355J0, S355J2,
C350, C350 L0 ect.
We
have three heat treatment furnace, two furnace of 100 mt, and one furnace of
300mt, that means we could finish 500mt goods at the same time.
Australia Square Steel Pipe,Galvanized Square Steel Pipe,Australia Carbon Steel Pipe,Australia Steel Metal Pipe
JINAN XIN JIYUAN SPECIAL SECTION TUBE CO., LTD. , https://www.squarepipes.com